May 11, 20197 yr I updated from v6.6.7 to v.6.7 without any problems. 👍 ASRockRack C2750D4I (BIOS v2.90) + 32GB ECC + 8x 10TB Seagate Ironwolf Is it possible to add a custom case model icon? (or is there any chance to add a Silverstone DS380 icon?)
May 11, 20197 yr 1 hour ago, calypsoSA said: Also upgraded and missing drives all over due to the marvell issue. Never had a problem before. Rolling back. Should this not be noted as a breaking change, as I imagine many people are going to be in the same situation. Same issue here, during boot it tried to access the drives but eventually gave up. Havent tried anythig that could change something, like a diffrent PCI-Slot or ACS override. Reroll worked. Agree on having a note in this thread or the release notes. It seems this is a known "potential" issue since RC and has not been fixed for those that are effected. IOMMU group 1: [8086:1901] 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor PCIe Controller (x16) (rev 07) [8086:1905] 00:01.1 PCI bridge: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor PCIe Controller (x8) (rev 07) [1b4b:9230] 02:00.0 SATA controller: Marvell Technology Group Ltd. 88SE9230 PCIe SATA 6Gb/s Controller (rev 11)
May 11, 20197 yr 3 hours ago, calypsoSA said: Also upgraded and missing drives all over due to the marvell issue. Never had a problem before. Rolling back. Should this not be noted as a breaking change, as I imagine many people are going to be in the same situation. I think this is a problem that only some people encounter? As far as I know everyone who tried the betas eventually got it working (unless they quietly rolled back to Stable without mentioning it) so it was not obvious that many users might encounter an issue? Have you tried the suggested solution of disabling VT-D to see if it works for you?
May 11, 20197 yr FWIW, I have a marvell controller (HighPoint Rocket 620 2-port) and upgrade went fine. IOMMU group 18: [1b4b:9120] 05:00.0 SATA controller: Marvell Technology Group Ltd. 88SE9120 SATA 6Gb/s Controller (rev 12) [1b4b:91a4] 05:00.1 IDE interface: Marvell Technology Group Ltd. 88SE912x IDE Controller (rev 12)
May 11, 20197 yr Marvell/VT-D issues are nothing new, see for example this thread, some users are more affected than others, it might get better or worse with any newer kernel, nothing that LT can fix directly, anyone than can afford to get them replaced with for example an LSI HBA should.
May 11, 20197 yr 23 minutes ago, bobokun said: Anyone else have any weird UI issues after updating? I'm not sure how to fix this. Start in safe mode, looks like a plugin is overwriting/modifying the style sheets.
May 11, 20197 yr So it appears that the update went smoothly ...however my apps and vms are not showing at all. Wut Do?
May 11, 20197 yr Regarding the Marvell Controller issues: I have Marvell controller and updated from 6.6.1 ----> 6.7.0 without any issue. Boots fine, Array Starts fine, posting this message on my Win10 VM. This is the Marvell Controller I use. IOMMU group 20: [1b4b:9172] 05:00.0 SATA controller: Marvell Technology Group Ltd. 88SE9172 SATA 6Gb/s Controller (rev 11) IOMMU group 21: [1b4b:9172] 06:00.0 SATA controller: Marvell Technology Group Ltd. 88SE9172 SATA 6Gb/s Controller (rev 11) IOMMU group 22: [1b4b:9172] 07:00.0 SATA controller: Marvell Technology Group Ltd. 88SE9172 SATA 6Gb/s Controller (rev 11)
May 11, 20197 yr 5 minutes ago, MrSage said: So it appears that the update went smoothly ...however my apps and vms are not showing at all. Wut Do? Post your diagnostics
May 11, 20197 yr Just now, MrSage said: What file do i need from here Post the complete downloaded zip file
May 11, 20197 yr Just now, bonienl said: Post the complete downloaded zip file tower-diagnostics-20190511-1422.zip
May 11, 20197 yr @MrSage Your "appdata" and "system" folders exist both on the cache device and array. Do the following: Stop the Docker service and VM service (see settings) Change the setting "Use cache disk" to Prefer for both the appdata share and the system share (see shares) Run the Mover (see main) Do a "compute all" on the share page to verify that these shares now only exist on the cache device Change the setting "Use cache disk" to Yes Only for both shares Edited May 11, 20197 yr by bonienl
May 11, 20197 yr 15 minutes ago, bonienl said: @MrSage Your "appdata" and "system" folders exist both on the cache device and array. Do the following: Stop the Docker service and VM service (see settings) Change the setting "Use cache disk" to Prefer for both the appdata share and the system share (see shares) Run the Mover (see main) Do a "compute all" on the share page to verify that these shares now only exist on the cache device Change the setting "Use cache disk" to Yes for both shares Should step 5 not be ‘Only’ (or leave it at Prefer).
May 11, 20197 yr 5 minutes ago, itimpi said: Should step 5 not be ‘Only’ (or leave it at Prefer). Also...ive been running "compute" for a while now...does it take a bit?
May 11, 20197 yr 36 minutes ago, bonienl said: @MrSage Your "appdata" and "system" folders exist both on the cache device and array. Do the following: Stop the Docker service and VM service (see settings) Change the setting "Use cache disk" to Prefer for both the appdata share and the system share (see shares) Run the Mover (see main) Do a "compute all" on the share page to verify that these shares now only exist on the cache device Change the setting "Use cache disk" to Yes for both shares Okay...so ive done all this and still no dice. Here is my latest diagnostics. tower-diagnostics-20190511-1517.zip
May 11, 20197 yr 21 minutes ago, itimpi said: Should step 5 not be ‘Only’ (or leave it at Prefer). Right, it should be ONLY (my mistake)
May 11, 20197 yr 2 minutes ago, MrSage said: Okay...so ive done all this and still no dice. Here is my latest diagnostics. These diagnostics still show the shares exist on the array. Post a screenshot of the Share page after a "compute all"
May 11, 20197 yr 36 minutes ago, bonienl said: These diagnostics still show the shares exist on the array. Post a screenshot of the Share page after a "compute all" Maybe I should just restore the previous version? Not sure what to do. Edited May 11, 20197 yr by MrSage
May 11, 20197 yr So I had to downgrade to 6.6.7 to bring my server back up and running. I was running perfect on the RC8.
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.