YoHoNoMo Posted January 15, 2022 Share Posted January 15, 2022 (edited) 4 hours ago, alturismo said: bitte mal ein screen von dem Fenster machen was da steht ... klick, klick ... Ja, das ist das Log, was @VK28.01 am Anfang zitiert hat. Da läuft ganz schnell immer wieder der gleiche Text durch. Offensichtlich so schnell, dass es mir fast die Unraid WebUI einfriert und ich Schwierigkeiten habe, den Docker zu stoppen, weil ich kaum noch in das Kontextmenü komme. Das reagiert aber zum Glück doch noch nach einer Weile. Quote ErrorWarningSystemArrayLogin -A, --abort Immediately abort -D, --dump Enable coredumps for daemon --noacl Disable all access control checks --nobat Disable DVB bouquets -j, --join Subscribe to a service permanently Testing options --tsfile_tuners Number of tsfile tuners --tsfile tsfile input (mux file) --tprofile Gather timing statistics for the code --thrdebug Thread debugging For more information please visit the Tvheadend website: https://tvheadend.org Usage: /usr/bin/tvheadend [OPTIONS] Generic options -h, --help Show this page -v, --version Show version information Service configuration -c, --config Alternate configuration path -B, --nobackup Don't backup configuration tree at upgrade -f, --fork Fork and run as daemon -u, --user Run as user -g, --group Run as group -p, --pid Alternate PID path -C, --firstrun If no user account exists then create one with no username and no password. Use with care as it will allow world-wide administrative access to your Tvheadend installation until you create or edit the access control from within the Tvheadend web interface. -a, --adapters Only use specified DVB adapters (comma-separated, -1 = none) --satip_bindaddr Specify bind address for SAT>IP server --satip_rtsp SAT>IP RTSP port number for server (default: -1 = disable, 0 = webconfig, standard port is 554) --nosatip Disable SAT>IP client --satip_xml URL with the SAT>IP server XML location Server connectivity -6, --ipv6 Listen on IPv6 -b, --bindaddr Specify bind address --http_port Specify alternative http port --http_root Specify alternative http webroot --htsp_port Specify alternative htsp port --htsp_port2 Specify extra htsp port --useragent Specify User-Agent header for the http client --xspf Use XSPF playlist instead of M3U Debug options -d, --stderr Enable debug on stderr -n, --nostderr Disable debug on stderr -s, --syslog Enable debug to syslog -S, --nosyslog Disable syslog (all messages) -l, --logfile Enable debug to file --debug Enable debug subsystems --trace Enable trace subsystems --subsystems List subsystems --fileline Add file and line numbers to debug --threadid Add the thread ID to debug --libav More verbose libav log --uidebug Enable web UI debug (non-minified JS) -A, --abort Immediately abort -D, --dump Enable coredumps for daemon --noacl Disable all access control checks --nobat Disable DVB bouquets -j, --join Subscribe to a service permanently Testing options --tsfile_tuners Number of tsfile tuners --tsfile tsfile input (mux file) --tprofile Gather timing statistics for the code --thrdebug Thread debugging For more information please visit the Tvheadend website: https://tvheadend.org Usage: /usr/bin/tvheadend [OPTIONS] Generic options -h, --help Show this page -v, --version Show version information Service configuration -c, --config Alternate configuration path -B, --nobackup Don't backup configuration tree at upgrade -f, --fork Fork and run as daemon -u, --user Run as user -g, --group Run as group -p, --pid Alternate PID path -C, --firstrun If no user account exists then create one with no username and no password. Use with care as it will allow world-wide administrative access to your Tvheadend installation until you create or edit the access control from within the Tvheadend web interface. -a, --adapters Only use specified DVB adapters (comma-separated, -1 = none) --satip_bindaddr Specify bind address for SAT>IP server --satip_rtsp SAT>IP RTSP port number for server (default: -1 = disable, 0 = webconfig, standard port is 554) --nosatip Disable SAT>IP client --satip_xml URL with the SAT>IP server XML location Server connectivity -6, --ipv6 Listen on IPv6 -b, --bindaddr Specify bind address --http_port Specify alternative http port --http_root Specify alternative http webroot --htsp_port Specify alternative htsp port --htsp_port2 Specify extra htsp port --useragent Specify User-Agent header for the http client --xspf Use XSPF playlist instead of M3U ..... [s6-finish] sending all processes the TERM signal. [s6-finish] sending all processes the KILL signal and exiting. Ich hab's... Das Template hat die Variable RUN_OPTS und die hat wiederum den Standard-Wert "run options here", wie man hier noch sehen kann: Der Text war durch das Template so voreingetragen, nehme ich an, was einen korrekten Start verhindert hat. 😄 Deswegen hatte es dann auch geklappt, als ich da etwas funktionierendes eingetragen habe. Ich habe den EIntrag aus meiner Config ganz gestrichen und jetzt läuft's. Edited January 15, 2022 by YoHoNoMo Quote des Log gekürzt, war viel zu lang... 4 Quote Link to comment
snowy00 Posted January 15, 2022 Share Posted January 15, 2022 (edited) 5 hours ago, alturismo said: also, der TVH Docker läuft hier auf 3 Maschinen problemlos ... natürlich ohne -C mode Beispiel und ich würde mal hier schauen zum Thema log, anscheinend passt ja etwas nicht ... bitte mal ein screen von dem Fenster machen was da steht ... klick, klick ... Kannst du mal den Screenshot deiner Docker config machen. Ich wollte auch mal die Version 4.3 ausprobieren vom Linuxser.io - hab die aber auch nicht zum laufen bekommen. Alles war ok - aber kein Zugriff auf WebUI. Das ist was bei mir im LOG steht wenn ich die aktuelle Version versuche zu installieren: Edited January 15, 2022 by snowy00 Quote Link to comment
alturismo Posted January 15, 2022 Share Posted January 15, 2022 18 minutes ago, snowy00 said: hab die aber auch nicht zum laufen bekommen. Alles war ok - aber kein Zugriff auf WebUI. da steht nichts interessantes drin, egal welchen Server ich nehme, schau mal ein post darüber, ich denke du hast den gleichen Fehler in deiner config ... 1 Quote Link to comment
snowy00 Posted January 15, 2022 Share Posted January 15, 2022 Oh, das habe ich überlesen - probiere es nachher! Quote Ich hab's... Das Template hat die Variable RUN_OPTS und die hat wiederum den Standard-Wert "run options here", wie man hier noch sehen kann: Danke 🙂 1 Quote Link to comment
snowy00 Posted January 16, 2022 Share Posted January 16, 2022 Quote Oh, das habe ich überlesen - probiere es nachher! Hab gerade auf 4.3 geupdated und funktioniert einwandfrei. 1 Quote Link to comment
VK28.01 Posted January 16, 2022 Author Share Posted January 16, 2022 Oho, dann hänge ich mich gleich mal dran und schaue, ob es auch bei mir läuft! Danke für den Tipp Alturisomo! Quote Link to comment
VK28.01 Posted January 23, 2022 Author Share Posted January 23, 2022 Jau, hier auch! Daumen hoch! 1 Quote Link to comment
Slarti123 Posted June 18, 2022 Share Posted June 18, 2022 On 1/15/2022 at 9:36 PM, YoHoNoMo said: Ich hab's... Das Template hat die Variable RUN_OPTS und die hat wiederum den Standard-Wert "run options here", wie man hier noch sehen kann: 1.000 Dank! Das war es auch bei mir Quote Link to comment
scooly Posted July 26, 2022 Share Posted July 26, 2022 Hallo Freunde ich hab das gleiche problem. Jedoch kenne ich mich nicht so gut aus. habe ein hardware update gemacht und jetzt läuft TvH. nicht mehr. Entweder habe ich kein Webinterface oder er zeit einen Fehler in der Einstellung bei /dev/dvb oder bei /dev/dri Quote Link to comment
scooly Posted July 26, 2022 Share Posted July 26, 2022 Just now, scooly said: Hallo Freunde ich hab das gleiche Problem. Jedoch kenne ich mich nicht so gut aus. habe ein Hardware update gemacht und jetzt läuft TvH. nicht mehr. Entweder habe ich kein Webinterface oder er zeigt einen Fehler in der Einstellung bei /dev/dvb oder bei /dev/dri Quote Link to comment
mgutt Posted July 27, 2022 Share Posted July 27, 2022 On 7/26/2022 at 2:44 PM, scooly said: Entweder habe ich kein Webinterface oder er zeit einen Fehler in der Einstellung bei /dev/dvb oder bei /dev/dri Wo zeigt er welchen Fehler? Quote Link to comment
sakistech Posted July 29, 2022 Share Posted July 29, 2022 gibt es Neuigkeiten dazu? habe den selben fehler. Quote Link to comment
ich777 Posted July 31, 2022 Share Posted July 31, 2022 On 7/26/2022 at 2:44 PM, scooly said: Webinterface oder er zeit einen Fehler in der Einstellung bei /dev/dvb oder bei /dev/dri On 7/30/2022 at 12:20 AM, sakistech said: gibt es Neuigkeiten dazu? habe den selben fehler. Welchen Fehler habt ihr denn beide, was zeigt das Docker run command an? (um diesen output zu bekommen einfach im Docker template was ändern und wieder zurück ändern, beispielsweise den letzten Buchstaben vom Namen löschen und wieder hinzufügen um den Apply button am ende frei zu schalten und dann auf Apply klicken) Funktionieren denn eure Geräte (DVB und Intel) auch und habt ihr auch die zugehörigen Pfade (/dev/dvb und /dev/dri)? Quote Link to comment
sakistech Posted July 31, 2022 Share Posted July 31, 2022 (edited) Hi, ja installieren tut es alles wie es soll, nur geht ohne "-C" unter RUN_OPTS: das WebUI nicht auf. Edit: jetzt wollte ich einen neuen suchlauf machen und dann kommt folgende fehlermeldung in tvh: 2022-07-31 21:27:33.573 mpegts: 11362H in Astra - scan no data, failed 2022-07-31 21:27:33.573 subscription: 0004: "scan" unsubscribing Edit 2: hab jetzt folgendes unter Extra Parameters eingetragen und es geht. Edited August 2, 2022 by sakistech Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.