Jump to content

JorgeB

Moderators
 View Profile  See their activity

  • Posts

    67,644

  • Joined

  • Last visited

  • Days Won

    707

 Content Type 

Everything posted by JorgeB

  1. JorgeB
    Changed Status to Closed Changed Priority to Other
  2. JorgeB
    RAM is running at 3600MT/s, max supported speed for you CPU with 4 dual rank DIMMs is 2667 MT/s, in any case this is general support issue, so please continue discussion here:
  3. JorgeB
    reiserfsck --rebuild-sb /dev/sde1 Follow the instructions carefully, once it's done: reiserfsck --rebuild-tree /dev/sde1 This last one will take several hours.
  4. JorgeB
    OK, just wanted to make sure since some users expect replacing cables/controller fixes a disable disks. First diags show a successful rebuild, second ones show a rebuild in progress, there are some ATA errors though, you say it's always the same disk that gets disable, even if you connect it to a different controller?
  5. JorgeB
    xfs_repair didn't damage anything since it was run in read-only mode (-n), but it was a waste of time.
  6. JorgeB
    I did ask if it was XFS... Try rebuild the superblock, then you'll need to run reiserfsck again with --rebuild-tree: https://wiki.unraid.net/Check_Disk_Filesystems#Rebuilding_the_superblock
  7. JorgeB
    JMB585 usually works fine with Unraid. Not clear if you then rebuilt the disk and it happen again, because once a disk is disable it needs to be rebuilt.
  8. JorgeB
    In the board BIOS there should be a "idle power supply control" setting.
  9. JorgeB
    Diags are all after rebooting so not much to see, you can try this but by the description it sounds more like a hardware issue, and in that case it may not log anything.
  10. JorgeB
    Best bet is to post on the docker support thread, if there is one:
  11. JorgeB
    That and your other problem suggest the flash drive is not mounting correctly, recreate it or try a different one.
  12. JorgeB
    Respect max officially support RAM speeds with Ryzen or you'll likely run into trouble.
  13. JorgeB
    Make sure mover logging is enable, run the mover then grab and post diags.
  14. JorgeB
    After booting type "diagnostics" in the console and then attach them here.
  15. JorgeB
    Not just that, also netfilter call traces mentioned in the second link, also worth trying this: https://forums.unraid.net/bug-reports/stable-releases/690691-kernel-panic-due-to-netfilter-nf_nat_setup_info-docker-static-ip-macvlan-r1356/?do=findComment&comment=14530
  16. JorgeB
    This will happen if the share's minimum free space setting is not correctly set, it should be set to twice the max file size you expect to copy to that share.
  17. JorgeB
    Sounds like a plex problem then, you can try the plex forum or the docker support thread.
  18. JorgeB
    For any further controller related discussion please use the new thread:
  19. JorgeB
    You can also try this: https://forums.unraid.net/bug-reports/stable-releases/690691-kernel-panic-due-to-netfilter-nf_nat_setup_info-docker-static-ip-macvlan-r1356/?do=findComment&comment=14530
  20. JorgeB
    You can run them all at the same time.
  21. JorgeB
    No, I meant reformatting the disk.
  22. JorgeB
    Once a disk gets disable it needs to be rebuilt (or do a new config).
  23. JorgeB
    I meant does it get better if you stop everything after the problem starts?
  24. JorgeB
    Try recreating the flash drive.
  25. JorgeB
    The easiest solution is to rebuild them one by one so the partition can be correctly recreated: https://forums.unraid.net/topic/84717-moving-drives-from-non-hba-raid-card-to-hba/ If it's really a RAID controller you should avoid that, or may need to repeat the same if you change controllers again in the future.
×
×
  • Create New...