Vr2Io

Docker are use Unraid DNS setting, it won't use LAN DHCP even allocate IP.

That's great 😃

At the most right side, does "arrow" point upward ? Anyway just click it to check any different.

When machine in sleep ( S3 S4 S5 ) does ethernet still link up ? If not, WOL won't work, no matter what you do.

Your DNS setting was automatic but DNS server still empty, pls check your router DHCP's DNS setting. A normal one was IP in semi-transparent when got the DNS info. from DHCP.

Pls try use IP access SMB in Windows, i.e. \\10.0.0.1 Your eth1 10.0.0.1 setting subnet in /24, so Windows side need setting to 255.255.255.0 instead 255.0.0.0

Unraid won't do NAT, you need a router gateway in 192.168.20.1 for accessing Internet for VLAN20. To access that container, client also need in same subnet & network.

Your Pihole was docker ? Where it put to, br0, 1, 2 ? Don't set same subnet to different interface.

Sorry typo the command line, it is wipefs -a /dev/sdX X is the drive letter The UD / Unraid GUI method also work, bu CLI much more easy.

9300-8e haven't power socket or need external power.

You can use command line wipefs -a /dev/devX to remove all partition.

For fan noise, you can replace some quiet fan to solve if you won't troubleshoot why full speed currently. For 12 disk, a single 6gb link already enough. No much selling point to make change.

用 Wan 口 會受限於路由表現吧.

I mean new mobo haven't solve the problem.

你測試是同一個 subnet, 192.168.3.x 192.168.100.x ?

OMG

These great, I think 1s delay on not a problem.

If boot to safe mode, same ?

Any progress in your build ? I make some modify to mount the fan on plastic mount outside, as result, the fan now more close to the blackplane. The aim were make more air pressure to push more air out ( pls note I reverse the airflow direction from rear to front ) , btw the test got positive result. So I have order 3 Arctic P12 Max to replace Arctic F12, the noise level have double, but I can adjust its speed by PWM, I would expect 50%-60% of P12 Max will be same as F12 (100%), after that I can cool more if I accept more noise. P12 Max really cheap.

USB power not a good source to control SSR on/off, because it may on / off during server booting / initial. Current sensing (normal open) switch more suitable for this case, but you need found a device have enough switching capability. Pls also confirm does EMC KTN-STL3 will power on once AC input have power. Those switch no need external power, only need main wire pass-through it. !! Below are example only !!. https://a.co/d/8eiFl3s

Provide network settings and docker page screen dump for ref.

Strange, all my build were latest, no problem.

Umm ..... I don't think Wing 4 will be such large different ( too good to be true ), I browse different YT review also not found such outcome. Below YT test said PPC3000 should be around 134.1 CFM and 5.664 mm H₂O. Pressure really importance, airflow seriously block in a rack when insert all harddisk, we need strong pressure to push out air. ( That's also why I point out the gap between fan and fan plate. ) Below YT have review Lian Li P28 ( have PPC3000 ) , it seems quite good for restricted airflow situation, cheaper a lot (2/3 price) and have 3 speed range too. I really have some interest !!! https://www.youtube.com/embed/AeOvOeTbCrA?si=Jdo4OGZTbX36Yc7d&start=405 There have three side for housing contact with fan, all three side with 3M tape ? This seems some difficult . For me, I prefer drill mount hole in fan plate if haven't.

Update mobo / CPU usually plug and play, I perform change several time just need modify some temperature or fan sensor setting.

Unraid Connect have public update in few min. ago, to be honest no surprise because not much different as previous flow. 😉