Dynamix - V6 Plugins

[Kasjo]

Hi all.

 

So now tih unraid 6.12 the monitor and selection from S3 sleep plugin works on my Server. Only the TCP Monitor still wont work. There is no info shown in the syslog that its started. It stareted right aways the extra delay before shutdown without even check for network activity

 

And yes, its active due the Settings from S3 sleep. But wont start. Any clue what to do here or any hope of a update?

Edited June 16, 2023 by Kasjo

[craigr]

On 6/15/2023 at 3:07 AM, bonienl said:

 

The capacity is as reported by your BIOS, only a fix in the BIOS of your motherboard can resolve it.

 

 

 

 

I hope they fix their DMI table info on the next firmware...  maybe I'm a little too detail oriented 🤪

[kiwijunglist]

Hi

 

I couldn't get dynamix fan control plugin to work.

 

I have subsequently found out that the dynamix fan plugin only works if you have installed the dyanmix system temp plugin

 

I think this is a bit unclear with the documentation.  I suggest that the dynamix plugin throws a warning if the system temp plugin is not installed.

 

[spl147]

Hi
 
I couldn't get dynamix fan control plugin to work.
 
I have subsequently found out that the dynamix fan plugin only works if you have installed the dyanmix system temp plugin
 
I think this is a bit unclear with the documentation.  I suggest that the dynamix plugin throws a warning if the system temp plugin is not installed.
 

That is not true, all you need to do is run sensors-detect and then load the drivers detected into the fan speed plugin

[kiwijunglist]

Thanks... From my experience, on my system , it didn't work (detect button greyed out and can't be clicked and can't choose anything on the PWM controller drop down menu ) and I tried that .... but after installing the dyanmix temp plugin everything was able to be selected etc.

Edited June 18, 2023 by kiwijunglist

[ds9]

Anybody using 6.12 or 6.12.1 with S3 sleep plugin ? I wanted to give this plugin a try on my NAS on my QNAP.

Seems this hardware support S3 :

dmesg : [    0.704022] ACPI: PM: (supports S0 S3 S5)

I used a basic S3 configuration and I can wake up my device -  I installed  this program : https://github.com/sabhiram/go-wol

to send WOL packet. But only ping is working (the Web interface / and i guess other processes) when server wakes up.
I had unfortunately no logs after reboot. Issue occured 3 times I tried to use sleep.

I gave it another try  - after changing configuration to keep logs on USB key, and got can see the following message :


Looking at logs I see :

Jun 19 15:50:13 Tower kernel: usb 2-1: USB disconnect, device number 2
Jun 19 15:50:13 Tower kernel: device offline error, dev sda, sector 5802129 op 0x1:(WRITE) flags 0x0 phys_seg 7 prio class 2
Jun 19 15:50:13 Tower kernel: Buffer I/O error on dev sda2, logical block 5800081, lost async page write
Jun 19 15:50:13 Tower kernel: Buffer I/O error on dev sda2, logical block 5800082, lost async page write
Jun 19 15:50:13 Tower kernel: Buffer I/O error on dev sda2, logical block 5800083, lost async page write
Jun 19 15:50:13 Tower kernel: Buffer I/O error on dev sda2, logical block 5800084, lost async page write
Jun 19 15:50:13 Tower kernel: Buffer I/O error on dev sda2, logical block 5800085, lost async page write
Jun 19 15:50:13 Tower kernel: Buffer I/O error on dev sda2, logical block 5800086, lost async page write
Jun 19 15:50:13 Tower kernel: Buffer I/O error on dev sda2, logical block 5800087, lost async page write
Jun 19 15:50:13 Tower kernel: device offline error, dev sda, sector 5802456 op 0x1:(WRITE) flags 0x0 phys_seg 1 prio class 2
Jun 19 15:50:13 Tower kernel: device offline error, dev sda, sector 2049 op 0x1:(WRITE) flags 0x100000 phys_seg 1 prio class 2
Jun 19 15:50:13 Tower kernel: Buffer I/O error on dev sda2, logical block 1, lost async page write
Jun 19 15:50:13 Tower kernel: device offline error, dev sda, sector 7714 op 0x1:(WRITE) flags 0x100000 phys_seg 1 prio class 2
Jun 19 15:50:13 Tower kernel: Buffer I/O error on dev sda2, logical block 5666, lost async page write
Jun 19 15:50:13 Tower kernel: device offline error, dev sda, sector 22946 op 0x1:(WRITE) flags 0x100000 phys_seg 1 prio class 2
Jun 19 15:50:13 Tower kernel: Buffer I/O error on dev sda2, logical block 20898, lost async page write
Jun 19 15:50:13 Tower kernel: device offline error, dev sda, sector 160848 op 0x1:(WRITE) flags 0x100000 phys_seg 1 prio class 2
Jun 19 15:50:13 Tower kernel: device offline error, dev sda, sector 160848 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
Jun 19 15:50:13 Tower kernel: device offline error, dev sda, sector 5802456 op 0x1:(WRITE) flags 0x800 phys_seg 1 prio class 2
Jun 19 15:50:13 Tower kernel: FAT-fs (sda2): unable to read inode block for updating (i_pos 2540807)
Jun 19 15:50:13 Tower kernel: FAT-fs (sda2): unable to read inode block for updating (i_pos 2540807)

My USB key is no faulty :  there is an Unraid 6.12 (kernel 6.1.x)  + plugin combination  issue ?
Seems like USB disconnect/connect issue . I didn't have any issue with my key previously.
My key still appears through lsusb : Bus 002 Device 004: ID 0781:558a SanDisk Corp. Ultra but there is no /dev/sda after suspend  :

root@Tower:~# fdisk  -l /dev/sda
fdisk: cannot open /dev/sda: No such file or directory

Logs I gathered :

 

[ 2150.829940] PM: suspend exit
[ 2150.886828] sda: detected capacity change from 120176640 to 0
[ 2151.035860] usb 2-1: USB disconnect, device number 2
[ 2151.037738] device offline error, dev sda, sector 6693673 op 0x1:(WRITE) flags 0x0 phys_seg 7 prio class 2

 

I tried the following  USB with no success :

 

echo -1 > /sys/module/usbcore/parameters/autosuspend 

and also adding  usbcore.autosuspend=-1 as boot option.
 

I don't know how to solve this USB key & sleep issue.

Edited July 1, 2023 by ds9
Additional infos

[jcarre]

I'm having a problem with the new update regarding system temp/auto fan.
The drivers load as usual but the array speed fan shows blank.
I have an x570 Aorus Motherboad.
None of the pwm fans are detected.

EDIT: Fixed it by installing "ITE IT87 Driver" Plugin!!
 

Edited June 20, 2023 by jcarre

[stephack]

On 6/15/2023 at 9:40 AM, dopeytree said:

Updated to 6.12

 

Then my PSU gave up.. it even made that electric zapping noise as some dodgy Chinese component must have finally given up. (it had been randomly rebooting for a while).

Have swapped to a temporary MAG PSU while a new 1u flex psu arrives tomorrow.

 

Powered up started a parity check. 

 

Then went for lunch. Came back an hour later and s3 sleep had activated during parity check.

 

Have disable sleep until any further comment from others.

 

 

I just updated to 6.12.1 and I'm having a similar S3 sleep issue. After the update my system started a parity check. My server has gone to sleep 3 times during the check. Looks like I'll have to disable until the Parity check completes but now I'm concerned that it might go to sleep during one of my automated backups. Hopefully this plugins gets some love 6.12 update love soon.

[dopeytree]

I got sleep working again and has been fine for a few days.

 

• Add any array drives to monitored disks.
• I also changed the time from what I think used to be 30s (is now minutes) to 1 for 1 minute.
• Also upped the network chatter to 500Kb. May reduce this in the future.
• I have it set to exclude the cache.

Edited June 24, 2023 by dopeytree

[stephack]

On 6/24/2023 at 6:25 PM, dopeytree said:

I got sleep working again and has been fine for a few days.

 

• Add any array drives to monitored disks.
• I also changed the time from what I think used to be 30s (is now minutes) to 1 for 1 minute.
• Also upped the network chatter to 500Kb. May reduce this in the future.
• I have it set to exclude the cache.

Thanks for the suggestions. I added all my disks to the "monitor disks outside of the array" list and it seems to have fixed my sleep issue. Strange that we suddenly now have to include the disks independently of the array...but it's a simple enough fix I guess.

Edited June 26, 2023 by stephack

[WoRie]

Hi,

 

I have 5 80mm Arctic 4 pin PWM fans installed, all connected to my MB. 2 of the 5 are connected in series but then to the mb, the last one in the screenshot is a smaller noctua fan.

I set all low temp / high temp points for the disks and minimal PWM values. The values are being displayed in the bottom bar of Unraid. However, some show up as 0% duty cycle, while others correctly display the current level.

 

I hit detect on each of the controllers again and adjusted all points, but the results are the same. Any idea what the problem is? Also, can I rename these fans somehow. It's hard to remember, which fan cools which part.

 

[spl147]

Hi,
 
I have 5 80mm Arctic 4 pin PWM fans installed, all connected to my MB. 2 of the 5 are connected in series but then to the mb, the last one in the screenshot is a smaller noctua fan.

I set all low temp / high temp points for the disks and minimal PWM values. The values are being displayed in the bottom bar of Unraid. However, some show up as 0% duty cycle, while others correctly display the current level.
 
I hit detect on each of the controllers again and adjusted all points, but the results are the same. Any idea what the problem is? Also, can I rename these fans somehow. It's hard to remember, which fan cools which part.
 

Split them all to the same header and call it a day

[JudasD]

Dynamix Safe Mode is super handy for anyone having dashboard issues with their plugins.  I am still having issues trying to find which plug-in is causing my dashboard to show blank, but this plug-in prevents needing the constant reboots.  Very nice!!!

 

Edited June 29, 2023 by JudasD

[dopeytree]

How would I make the s3 sleep plugin spin drives down before sleeping?

 

6.12.1

Edited June 29, 2023 by dopeytree

[Masterwishx]

@bonienl can you explain please how new plugin (Safe Mode) work ? 

[bonienl]

43 minutes ago, Masterwishx said:

@bonienl can you explain please how new plugin (Safe Mode) work ? 

 

This plugin allows the user to run the GUI with or without plugins. Click on the 'X' icon to switch between modes.

Note that plugins are only disabled for the GUI, but not other tasks or jobs they have created themselves.

The idea of this plugin is to quickly test the GUI in case something doesn't work and determine whether a plugin is causing this.

 

[PicPoc]

Hi !
I use Dynamix System Stats and it's a really nice program ! thanks.
I wanted to know how change values of bars for discs :
-On a machine I have only one disc and it looks like this :

-I wanted to see bigger like this :

Is it possible ?
Thanks !

 

I'm on unraid v6.9.2.

Edited July 2, 2023 by PicPoc

[Conan the Barbarian]

Hi,

 

using a Gigabyte mobo x670e with a Ryzen 9 7900.

The plugin system info shows all the information perfectly.

But the system temp doesn’t detect any sensor.

do you know if there is still no support for am5?

thanks

[Mat W]

On 6/29/2023 at 12:33 PM, JudasD said:

Dynamix Safe Mode is super handy for anyone having dashboard issues with their plugins.  I am still having issues trying to find which plug-in is causing my dashboard to show blank, but this plug-in prevents needing the constant reboots.  Very nice!!!

 

I'll 2nd that!!!  Only wish there was a way to disable individual plugins rather than removing them, but I'll take preventing reboots.

[Vr2Io]

On 6/10/2023 at 5:27 PM, Vr2Io said:

System stats plugin have swap read / write reading in 6.12rc6 & 7, have try server reboot. But no problem on 6.11.5

 

Below are reading on array disk, but STATS show it is writing, same on UD disk.

 

Bump, when will fix storage read/write figure problem. Thanks

[MAM59]

System Stats "strange" on 6.12.2

One would expect more than just green color on disk 1, but ?!?!?! Hmmm

 

Also, on the System Stats page I see Writes per Second, but no Reads ?!?!?

(increadable slow writes for an rsync copy job... zfs is baaad)

 

[PicPoc]

On 7/2/2023 at 8:44 AM, PicPoc said:

Hi !
I use Dynamix System Stats and it's a really nice program ! thanks.
I wanted to know how change values of bars for discs :
-On a machine I have only one disc and it looks like this :

-I wanted to see bigger like this :

Is it possible ?
Thanks !

 

I'm on unraid v6.9.2.

Bump !

[Nackophilz]

On 6/20/2023 at 10:11 PM, jcarre said:

I'm having a problem with the new update regarding system temp/auto fan.
The drivers load as usual but the array speed fan shows blank.
I have an x570 Aorus Motherboad.
None of the pwm fans are detected.

EDIT: Fixed it by installing "ITE IT87 Driver" Plugin!!
 

Good too know ! 

Do you successfully control your fan ? I have an X570 too, IT87 plugin installed, but seems i can control them, they juste even if it 1% or 100% the fan speed at the same speeds ..

[comet424]

@bonienl  i had a suggestion couple years ago but still like to see it for the System Fan

an option to label each PWM to give it a real Name  thats linked to FAN Airflow on the Dashboard page...  in past i edited the Dashboard page and renamed FAN0 FAN1 FAN2 etc  but i forgotten

 

it be nice if we can Label  like  PWM1 , Label or friendly name    be like CPU Fan 

and then on the Dashboard  it would show up instead of FAN1 it show up as CPU Fan.. so it be easier to see what is what..

[PicPoc]

Does bonienl read this thread ?